Electric Bike Factory Introduces What Is The Cantilever Brake Adjustment Of Electric Vehicle
2020年10月14日Electric Bike Factory introduces the related knowledge of electric vehicle cantilever brake adjustment.
Loosen the brake shoe adjusting nut so that the brake shoe can contact the center of the rim in parallel, and the side surface should be aligned with the rim, and then tighten the brake shoe adjusting nut.
Turn the elastic rope nut, remove the hoisting cable from the bridge, adjust the distance between the brake skin and the rim to about 2-3mm, and adjust the hoisting cable to a suitable length (it is advisable that the cable does not touch the mud plate in the non-braking state), and then tighten the cable nut tightly. Loosen the bridge nut, hang the brake rope on the bridge, adjust the brake rope to a suitable length, and tighten the bridge nut.
In the non-braking state, if the brake shoe cannot be reset and still contacts the rim, loosen the connecting bolt properly or add some lubricating oil here, so that the torsion spring can rotate freely. Oil is prohibited at rim friction.
Adjust the front wheel drum brake, and adjust the adjusting bolt to minimize the gap between the brake disc and the brake skin without interference.
The above content is organized and shared by Fast Sport Electric Motorbike Manufacturer , hoping to help those in need.
Loosen the brake shoe adjusting nut so that the brake shoe can contact the center of the rim in parallel, and the side surface should be aligned with the rim, and then tighten the brake shoe adjusting nut.
Turn the elastic rope nut, remove the hoisting cable from the bridge, adjust the distance between the brake skin and the rim to about 2-3mm, and adjust the hoisting cable to a suitable length (it is advisable that the cable does not touch the mud plate in the non-braking state), and then tighten the cable nut tightly. Loosen the bridge nut, hang the brake rope on the bridge, adjust the brake rope to a suitable length, and tighten the bridge nut.
In the non-braking state, if the brake shoe cannot be reset and still contacts the rim, loosen the connecting bolt properly or add some lubricating oil here, so that the torsion spring can rotate freely. Oil is prohibited at rim friction.
Adjust the front wheel drum brake, and adjust the adjusting bolt to minimize the gap between the brake disc and the brake skin without interference.
The above content is organized and shared by Fast Sport Electric Motorbike Manufacturer , hoping to help those in need.
Electric Vehicle Manufacturers introduces the use skills of new batteries:
1. Avoid overcharging
When the charger shows that it is full, it stops charging. It can’t be charged overnight or even several days. Overcharging will cause the active material of the plate to harden and fall off, and cause water loss and battery deformation. The battery runs in high temperature seasons, and there is mainly an overcharge problem. Therefore, in summer, the battery temperature should be reduced as much as possible to ensure good heat dissipation, to prevent charging immediately after exposure to the hot sun, and keep away from heat sources.
2. Avoid long-term power loss
In low temperature conditions, charging mainly has the problems of poor charging acceptance and insufficient charging, which will cause the battery to lose power. Long-term loss of power will cause the plate to vulcanize. Thermal insulation and anti-freezing measures should be taken at low temperatures, especially when charging should be placed in a warm environment, which will help ensure sufficient electricity, prevent irreversible sulfation, and extend the service life of the battery.
3. Prevent short circuit of battery installation
Particular care should be taken during installation or use. The tools used should be insulated. When wiring, the electrical appliances other than the battery should be connected first. After inspection, there is no short circuit. Finally, the battery should be connected. The wiring specifications should be well insulated to prevent overlapping pressure. rupture. It is forbidden to use the battery short-circuit method to detect the charging status of the battery to prevent the explosion and cause casualties.
4. Avoid long-term high-current discharge of the battery
Will greatly damage the internal structure of the battery. It is recommended that the owner should not start more than 5 seconds each time. Two consecutive starts are required, with an interval of 10-15 seconds.
5. Prevent exposure to the sun
Exposure to the sun will increase the temperature of the battery and increase the activity of the active materials in the battery, which will affect the service life of the battery.
The above content is organized and shared by Sport High Power E-Bike Manufacturer, hoping to help those in need.
1. Avoid overcharging
When the charger shows that it is full, it stops charging. It can’t be charged overnight or even several days. Overcharging will cause the active material of the plate to harden and fall off, and cause water loss and battery deformation. The battery runs in high temperature seasons, and there is mainly an overcharge problem. Therefore, in summer, the battery temperature should be reduced as much as possible to ensure good heat dissipation, to prevent charging immediately after exposure to the hot sun, and keep away from heat sources.
2. Avoid long-term power loss
In low temperature conditions, charging mainly has the problems of poor charging acceptance and insufficient charging, which will cause the battery to lose power. Long-term loss of power will cause the plate to vulcanize. Thermal insulation and anti-freezing measures should be taken at low temperatures, especially when charging should be placed in a warm environment, which will help ensure sufficient electricity, prevent irreversible sulfation, and extend the service life of the battery.
3. Prevent short circuit of battery installation
Particular care should be taken during installation or use. The tools used should be insulated. When wiring, the electrical appliances other than the battery should be connected first. After inspection, there is no short circuit. Finally, the battery should be connected. The wiring specifications should be well insulated to prevent overlapping pressure. rupture. It is forbidden to use the battery short-circuit method to detect the charging status of the battery to prevent the explosion and cause casualties.
4. Avoid long-term high-current discharge of the battery
Will greatly damage the internal structure of the battery. It is recommended that the owner should not start more than 5 seconds each time. Two consecutive starts are required, with an interval of 10-15 seconds.
5. Prevent exposure to the sun
Exposure to the sun will increase the temperature of the battery and increase the activity of the active materials in the battery, which will affect the service life of the battery.
The above content is organized and shared by Sport High Power E-Bike Manufacturer, hoping to help those in need.
Electric Motorcycle Factory introduces various functional knowledge of electric vehicles
1. Motor lock system: In the alert state, the controller automatically locks the motor when the alarm occurs. The controller has almost no power consumption. There are no special requirements for the motor. In the case of battery Undervoltage or other abnormal conditions, there is no normal promotion of electric vehicles. influences.
2. Self-checking function: dynamic self-checking and static self-checking, as long as the controller is powered on, it will automatically detect the relevant interface status, such as the handle, brake lever or other external switches, etc., once a failure occurs, The controller automatically implements protection to fully ensure the safety of riding. When the fault is removed, the protection status of the controller will be automatically restored.
3. Anti-charging function: the energy generated by EABS is fed back to the battery when braking, decelerating, or sliding downhill, which has the effect of anti-charging, thereby maintaining the battery, extending the battery life, and increasing the mileage .
4. Stall protection function: Automatically judge whether the motor is in full stall state or running state or motor short circuit state when over current, if the overcurrent is in running state, the controller sets the current limit value at a fixed value, In order to maintain the driving capacity of the vehicle; if the motor is in a pure locked-rotor state, the controller will control the current limit value below 10A after 2 seconds to protect the motor and the battery and save energy; if the motor is in a short circuit state, the controller Keep the output current below 2A to ensure the safety of the controller and battery.
9. Anti-speeding function: solves the speeding phenomenon caused by the handle of the brushless electric vehicle controller or the fault of the line, and improves the safety of the system.
5.1 + 1 power assist function: The user can adjust the self-assisted power or reverse power assist to realize the supplementary power during riding, which makes the rider feel more relaxed.
6. Anti-theft alarm function: ultra-quiet design, the introduction of automotive-grade remote control anti-theft concept, the stability of anti-theft is higher, the motor can be locked under the alarm state, the sound effect of the alarm horn is as high as 125dB, and has a strong deterrent. And has a self-learning function, the remote control distance is up to 150 meters without error codes.
7. Reversing function: the controller adds a reversing function. When the user is riding normally, the reversing function is invalid; when the user stops, press the reversing function key to perform auxiliary reversing, and the maximum reversing speed does not exceed 10km / h.
The above content is shared by High Power Electric Motorcycle Factory in the hope of helping those in need.
1. Motor lock system: In the alert state, the controller automatically locks the motor when the alarm occurs. The controller has almost no power consumption. There are no special requirements for the motor. In the case of battery Undervoltage or other abnormal conditions, there is no normal promotion of electric vehicles. influences.
2. Self-checking function: dynamic self-checking and static self-checking, as long as the controller is powered on, it will automatically detect the relevant interface status, such as the handle, brake lever or other external switches, etc., once a failure occurs, The controller automatically implements protection to fully ensure the safety of riding. When the fault is removed, the protection status of the controller will be automatically restored.
3. Anti-charging function: the energy generated by EABS is fed back to the battery when braking, decelerating, or sliding downhill, which has the effect of anti-charging, thereby maintaining the battery, extending the battery life, and increasing the mileage .
4. Stall protection function: Automatically judge whether the motor is in full stall state or running state or motor short circuit state when over current, if the overcurrent is in running state, the controller sets the current limit value at a fixed value, In order to maintain the driving capacity of the vehicle; if the motor is in a pure locked-rotor state, the controller will control the current limit value below 10A after 2 seconds to protect the motor and the battery and save energy; if the motor is in a short circuit state, the controller Keep the output current below 2A to ensure the safety of the controller and battery.
9. Anti-speeding function: solves the speeding phenomenon caused by the handle of the brushless electric vehicle controller or the fault of the line, and improves the safety of the system.
5.1 + 1 power assist function: The user can adjust the self-assisted power or reverse power assist to realize the supplementary power during riding, which makes the rider feel more relaxed.
6. Anti-theft alarm function: ultra-quiet design, the introduction of automotive-grade remote control anti-theft concept, the stability of anti-theft is higher, the motor can be locked under the alarm state, the sound effect of the alarm horn is as high as 125dB, and has a strong deterrent. And has a self-learning function, the remote control distance is up to 150 meters without error codes.
7. Reversing function: the controller adds a reversing function. When the user is riding normally, the reversing function is invalid; when the user stops, press the reversing function key to perform auxiliary reversing, and the maximum reversing speed does not exceed 10km / h.
The above content is shared by High Power Electric Motorcycle Factory in the hope of helping those in need.
High Speed Electric Motorcycle Manufacturer introduces that lead-acid batteries also have three fears, the most fear of these three, once these three situations occur, the electric vehicle battery is basically scrapped, and the battery needs to be replaced!
1. The internal expansion of the battery:
If you find that the inside of your electric car battery is much larger than when you just bought it, it means that it is full of gas and it is completely damaged at this time and cannot be used anymore. Even if you can charge it, its endurance is very poor, so when you find that the battery becomes larger, you must replace it.
2. The battery temperature is extremely high when charging:
If you find that the battery temperature of your electric car is very high while charging, or even a little hot, it means that it is about to die. It may be because some internal elements are constantly being precipitated, and then the power during charging is increased, so that the battery will become very hot. At this time, the charging is fast and the power consumption is also fast. You may have to charge four or five times a day. Seriously, it may even cause a fire!
3. Cannot continue charging:
If your electric car is charging, the light is red. But no matter how long you charge it or the red light, it means that the battery inside the electric car is damaged and can no longer store power. At this time, the electric car will continue to charge until you unplug it. This situation is still relatively dangerous and often causes a fire, so once you find that your battery cannot be charged, you must replace it.
The above content is organized and shared by High Power Electric Motorcycle Manufacturer, hoping to help those in need.
1. The internal expansion of the battery:
If you find that the inside of your electric car battery is much larger than when you just bought it, it means that it is full of gas and it is completely damaged at this time and cannot be used anymore. Even if you can charge it, its endurance is very poor, so when you find that the battery becomes larger, you must replace it.
2. The battery temperature is extremely high when charging:
If you find that the battery temperature of your electric car is very high while charging, or even a little hot, it means that it is about to die. It may be because some internal elements are constantly being precipitated, and then the power during charging is increased, so that the battery will become very hot. At this time, the charging is fast and the power consumption is also fast. You may have to charge four or five times a day. Seriously, it may even cause a fire!
3. Cannot continue charging:
If your electric car is charging, the light is red. But no matter how long you charge it or the red light, it means that the battery inside the electric car is damaged and can no longer store power. At this time, the electric car will continue to charge until you unplug it. This situation is still relatively dangerous and often causes a fire, so once you find that your battery cannot be charged, you must replace it.
The above content is organized and shared by High Power Electric Motorcycle Manufacturer, hoping to help those in need.
Electric Motorcycle Factory introduced to add as much fluid as possible under the premise of ensuring no leakage to prolong or avoid the occurrence of "thermal runaway".
Avoid internal short circuit or micro short circuit, and the tendency of micro short circuit.
During use, over-discharge should be prevented and fully charged.
Strictly check the charger to avoid serious overcharging.
When charging at high temperature, it is necessary to ensure good heat dissipation of the battery. Cooling measures or methods to shorten the charging time should be taken, otherwise the charging should be stopped.
The phenomenon that the battery is gradually consumed when it is not working is called self-discharge. Self-discharge cannot be completely avoided. It is generally considered that it is normal to consume 1%~2% of its own capacity every day. If it exceeds this value, it is abnormal self-discharge.
The above content is organized and shared by High Speed Electric Motorcycle Manufacturer, hoping to help those in need.
Avoid internal short circuit or micro short circuit, and the tendency of micro short circuit.
During use, over-discharge should be prevented and fully charged.
Strictly check the charger to avoid serious overcharging.
When charging at high temperature, it is necessary to ensure good heat dissipation of the battery. Cooling measures or methods to shorten the charging time should be taken, otherwise the charging should be stopped.
The phenomenon that the battery is gradually consumed when it is not working is called self-discharge. Self-discharge cannot be completely avoided. It is generally considered that it is normal to consume 1%~2% of its own capacity every day. If it exceeds this value, it is abnormal self-discharge.
The above content is organized and shared by High Speed Electric Motorcycle Manufacturer, hoping to help those in need.
Electric Motorcycle Factory introduces the maintenance rules of electric vehicles
1. During the use of electric vehicles, users generally do not need to maintain and maintain the internal parts of the motor. They only need to pay attention to check the status of the fasteners of the electric hub installed on the rear fork. If there is any loose nut, tighten it in time Nuts or ask professionals to check and handle.
2. When the motor stops running, remove the dust and sludge from the motor in time, keep the motor clean and prevent oil and water from entering the motor. Do not spray directly with water when cleaning.
3. Check whether the motor lead wire is scratched, whether there is abnormal noise when the motor is running, if necessary, send it to our company’s sales office for treatment, and ask professionals to check and deal with it.
4. If chain motors are equipped, lubricate the chain regularly.
The above content is organized and shared by High Power Electric Motorcycle Manufacturer, hoping to help those in need.
1. During the use of electric vehicles, users generally do not need to maintain and maintain the internal parts of the motor. They only need to pay attention to check the status of the fasteners of the electric hub installed on the rear fork. If there is any loose nut, tighten it in time Nuts or ask professionals to check and handle.
2. When the motor stops running, remove the dust and sludge from the motor in time, keep the motor clean and prevent oil and water from entering the motor. Do not spray directly with water when cleaning.
3. Check whether the motor lead wire is scratched, whether there is abnormal noise when the motor is running, if necessary, send it to our company’s sales office for treatment, and ask professionals to check and deal with it.
4. If chain motors are equipped, lubricate the chain regularly.
The above content is organized and shared by High Power Electric Motorcycle Manufacturer, hoping to help those in need.
When electric vehicles are becoming more and more popular, the charger of electric vehicles has also attracted people’s attention, because this component is the energy source of this electric vehicle, so today High Speed Electric Motorcycle manufacturer will introduce the relevant knowledge about electric vehicles.
1. What is an electric car charger
An electric vehicle charger is a device that supplements electric energy to an electric bicycle battery: generally it is divided into two-stage charging mode and three-stage charging mode.
1. Two-stage charging mode: first constant voltage charging, the charging current gradually decreases with the increase of battery voltage, when the battery power is replenished to a certain level, the battery voltage will rise to the set value of the charger, and then it will be converted to trickle current Recharge.
2. Three-stage charging mode: At the beginning of charging, first charge with constant current and quickly replenish energy to the battery; after the battery voltage rises, switch to constant voltage charging. At this time, the battery energy is slowly replenished and the battery voltage continues to rise; reaching the charger’s charge When the voltage value is terminated, it is switched to trickle charge to maintain the battery and supply the battery’s self-discharge current.
The above is organized and shared by High Power Electric Motorcycle Manufacturers, hoping to help those in need.
1. What is an electric car charger
An electric vehicle charger is a device that supplements electric energy to an electric bicycle battery: generally it is divided into two-stage charging mode and three-stage charging mode.
1. Two-stage charging mode: first constant voltage charging, the charging current gradually decreases with the increase of battery voltage, when the battery power is replenished to a certain level, the battery voltage will rise to the set value of the charger, and then it will be converted to trickle current Recharge.
2. Three-stage charging mode: At the beginning of charging, first charge with constant current and quickly replenish energy to the battery; after the battery voltage rises, switch to constant voltage charging. At this time, the battery energy is slowly replenished and the battery voltage continues to rise; reaching the charger’s charge When the voltage value is terminated, it is switched to trickle charge to maintain the battery and supply the battery’s self-discharge current.
The above is organized and shared by High Power Electric Motorcycle Manufacturers, hoping to help those in need.
Electric Motorcycle Factory introduces the use of charging knowledge
1. Everyone should charge the electric car for 2-3 hours after the light turns green;
2. The principle is shallow discharge (electricity) and frequent charge (electricity). That is to say, every time you ride a bicycle to use 50% before charging, do not charge too often, otherwise it will easily shorten the battery life;
3. If you don’t ride for a long time, you should charge it regularly (1 month);
4. For long-term shallow-discharge batteries, deep discharge once every 3 months is the so-called light recharge. This is beneficial to the activation of long-term immobile substances in the deep part of the battery. Shining means that everyone should use electric vehicles until the controller battery undervoltage protection is activated.
The above content is organized and shared by the manufacturer of High Speed Electric Motorcycle , hoping to help those in need.
1. Everyone should charge the electric car for 2-3 hours after the light turns green;
2. The principle is shallow discharge (electricity) and frequent charge (electricity). That is to say, every time you ride a bicycle to use 50% before charging, do not charge too often, otherwise it will easily shorten the battery life;
3. If you don’t ride for a long time, you should charge it regularly (1 month);
4. For long-term shallow-discharge batteries, deep discharge once every 3 months is the so-called light recharge. This is beneficial to the activation of long-term immobile substances in the deep part of the battery. Shining means that everyone should use electric vehicles until the controller battery undervoltage protection is activated.
The above content is organized and shared by the manufacturer of High Speed Electric Motorcycle , hoping to help those in need.
Why does the motor of Fast Sport Electric Motorbike stop when it rotates?
1. If the battery is low, charge the battery.
2. The battery contacts are in poor contact, adjust the position of the contacts or polish the contacts.
3. Poor contact between the fuse tube and the fuse seat in the battery box, adjust or replace to make it good.
4. There is dirt in the photosensitive tube of the photosensitive film in the speed control handle. Clean or replace the photosensitive film and wipe the photosensitive tube. If the fault still cannot be eliminated, please replace the speed control handle.
5. There is a fault in the controller, replace or repair the controller.
6. The lead of the speed control handle seems to be broken. Replace or repair the lead.
7. If the brake power-off switch fails, adjust or replace the brake power-off switch.
8. The power lock has poor contact after ablation. Replace or repair the power lock.
9. Virtually connect the connectors in the circuit and reconnect them to make good contact.
10. The carbon brushes, wires and windings in the motor are welded or connected. Repair or replace the motor.
1. If the battery is low, charge the battery.
2. The battery contacts are in poor contact, adjust the position of the contacts or polish the contacts.
3. Poor contact between the fuse tube and the fuse seat in the battery box, adjust or replace to make it good.
4. There is dirt in the photosensitive tube of the photosensitive film in the speed control handle. Clean or replace the photosensitive film and wipe the photosensitive tube. If the fault still cannot be eliminated, please replace the speed control handle.
5. There is a fault in the controller, replace or repair the controller.
6. The lead of the speed control handle seems to be broken. Replace or repair the lead.
7. If the brake power-off switch fails, adjust or replace the brake power-off switch.
8. The power lock has poor contact after ablation. Replace or repair the power lock.
9. Virtually connect the connectors in the circuit and reconnect them to make good contact.
10. The carbon brushes, wires and windings in the motor are welded or connected. Repair or replace the motor.
The manufacturer of High Speed Electric Motorcycle analyzes whether to charge the electric car without running out of electricity or to wait for all the electricity to be used up before charging?
The less the amount of discharge, the more the number of recharges, which means the more cycles of use, which is harmful to the life of the battery.
If you want to use it for ten years and only charge and discharge eight times a year, then you only need to charge and discharge eighty times. This is good for the battery, but in fact, this is impossible. Most batteries are used in 300 Above the second cycle, so frequent charging will damage the battery greatly.
The less the amount of discharge, the more the number of recharges, which means the more cycles of use, which is harmful to the life of the battery.
If you want to use it for ten years and only charge and discharge eight times a year, then you only need to charge and discharge eighty times. This is good for the battery, but in fact, this is impossible. Most batteries are used in 300 Above the second cycle, so frequent charging will damage the battery greatly.
High Speed Electric Motorcycle manufacturers share the advantages of switched reluctance motors are:
1. Suitable for frequent start, stop and forward and reverse conversion operation. Switched reluctance motors have the characteristics of low starting current and high starting torque, so that the current impact during starting is small, the motor and controller heat generation is smaller than that during continuous rated operation, there are many controllable parameters, and the speed regulation performance is good. The main operating parameters for controlling the switched reluctance motor are the phase opening angle, related break angle, phase current amplitude and phase winding voltage. Therefore, there are many controllable parameters, and the control is flexible and convenient. According to the operation requirements of the motor and the condition of the motor, different control methods and parameter values can be used to make it run in the best state. It can also make it achieve a variety of different functions and specific characteristic curves.
2. Small loss and high efficiency. Because there is no winding copper loss in the rotor of the switched reluctance motor, plus many controllable parameters, it is flexible and convenient, so it is easy to achieve efficient and optimal control under a wide speed range and different loads. Its efficiency is below 87% in a wide range.
3. Easy to recycle. The stator and rotor materials use magnets, which are common silicon steel sheets. Therefore, the materials are easy to obtain and easy to recycle.
4. High temperature torque performance is good. Since the rotor does not generate heat during operation, cooling control is relatively easy, and it can be operated at high temperatures.
1. Suitable for frequent start, stop and forward and reverse conversion operation. Switched reluctance motors have the characteristics of low starting current and high starting torque, so that the current impact during starting is small, the motor and controller heat generation is smaller than that during continuous rated operation, there are many controllable parameters, and the speed regulation performance is good. The main operating parameters for controlling the switched reluctance motor are the phase opening angle, related break angle, phase current amplitude and phase winding voltage. Therefore, there are many controllable parameters, and the control is flexible and convenient. According to the operation requirements of the motor and the condition of the motor, different control methods and parameter values can be used to make it run in the best state. It can also make it achieve a variety of different functions and specific characteristic curves.
2. Small loss and high efficiency. Because there is no winding copper loss in the rotor of the switched reluctance motor, plus many controllable parameters, it is flexible and convenient, so it is easy to achieve efficient and optimal control under a wide speed range and different loads. Its efficiency is below 87% in a wide range.
3. Easy to recycle. The stator and rotor materials use magnets, which are common silicon steel sheets. Therefore, the materials are easy to obtain and easy to recycle.
4. High temperature torque performance is good. Since the rotor does not generate heat during operation, cooling control is relatively easy, and it can be operated at high temperatures.
Generally, the number of fully charged and discharged batteries is 500 times, and it is better to add distilled water for maintenance after 300 times, that is, 12 months. The most important thing is not to ride the battery under the low voltage condition, and do not leave it for more than 12 hours. If it is convenient, charge it immediately to replenish the energy. Next, the High Power Electric Motorcycle manufacturer introduces the precautions for the use of the battery:
1. Never lose electricity
The state of power loss means that the battery is not charged in time after use, and it is prone to sulfation. The lead sulfate crystals are attached to the polar plate, blocking the electric ion channel, causing insufficient charging, and the battery capacity is reduced. The longer the idle period is, the more serious the battery damage. When the battery is not in use, it should be charged once a month, which can keep the battery in a "healthy" state.
2. Regular inspection
In the course of use, if the continuous mileage of the electric vehicle suddenly drops by more than ten kilometers in a short period of time, it is likely that at least one battery in the battery pack is broken, the plate is softened, and the active material of the plate falls off.. At this time, you should go to the professional battery repair institution for inspection, repair or grouping in time.
3. Do not discharge with high current
When the electric vehicle is starting, manning, or going uphill, please use the pedal to help, try to avoid instant large current discharge. Large current discharge can easily lead to lead sulfate crystallization, thereby damaging the physical properties of the battery plate.
4. master the charging time
Under normal circumstances, the battery is charged at night, the average charging time is about 8 hours. If it is a shallow discharge (the driving distance is very short after charging), the battery will be fully charged soon, and overcharging will occur when charging continues, causing the battery to lose water and generate heat, reducing the battery life. Therefore, the battery is best to charge once when the depth of discharge is 60% to 70%. In actual use, it can be converted into riding mileage , and the necessary charging is performed according to the actual situation to avoid harmful charging.
5. Prevent high temperature exposure
Electric vehicles are strictly prohibited from exposure to sunlight. An excessively high temperature environment will increase the internal pressure of the battery and force the battery pressure limiting valve to open automatically. The direct consequence is to increase the water loss of the battery. Excessive water loss of the battery will inevitably lead to a decrease in battery activity and accelerate the softening of the polar plate. Body heat, fatal damage such as bulging and deformation of the shell.
1. Never lose electricity
The state of power loss means that the battery is not charged in time after use, and it is prone to sulfation. The lead sulfate crystals are attached to the polar plate, blocking the electric ion channel, causing insufficient charging, and the battery capacity is reduced. The longer the idle period is, the more serious the battery damage. When the battery is not in use, it should be charged once a month, which can keep the battery in a "healthy" state.
2. Regular inspection
In the course of use, if the continuous mileage of the electric vehicle suddenly drops by more than ten kilometers in a short period of time, it is likely that at least one battery in the battery pack is broken, the plate is softened, and the active material of the plate falls off.. At this time, you should go to the professional battery repair institution for inspection, repair or grouping in time.
3. Do not discharge with high current
When the electric vehicle is starting, manning, or going uphill, please use the pedal to help, try to avoid instant large current discharge. Large current discharge can easily lead to lead sulfate crystallization, thereby damaging the physical properties of the battery plate.
4. master the charging time
Under normal circumstances, the battery is charged at night, the average charging time is about 8 hours. If it is a shallow discharge (the driving distance is very short after charging), the battery will be fully charged soon, and overcharging will occur when charging continues, causing the battery to lose water and generate heat, reducing the battery life. Therefore, the battery is best to charge once when the depth of discharge is 60% to 70%. In actual use, it can be converted into riding mileage , and the necessary charging is performed according to the actual situation to avoid harmful charging.
5. Prevent high temperature exposure
Electric vehicles are strictly prohibited from exposure to sunlight. An excessively high temperature environment will increase the internal pressure of the battery and force the battery pressure limiting valve to open automatically. The direct consequence is to increase the water loss of the battery. Excessive water loss of the battery will inevitably lead to a decrease in battery activity and accelerate the softening of the polar plate. Body heat, fatal damage such as bulging and deformation of the shell.
Many people use electric flat cars, but little is known about the classification of electric flat car controllers. High Power Electric Motorcycle manufacturers explain how to classify electric flat car controllers:
1. According to the power classification:
High power, medium power and low power, small power is more suitable for electric vehicles.
2. According to the motor classification:
Brushed and brushless, the speed adjustment method is to use the pulse width to modulate.
3. Classification according to structure:
Integral and separated:
The integrated controller is the controller and the display assembled together, installed in a small box, there will be many small holes on the box, you can see the working status of the electric car from the small holes. What is the speed, how much battery is left, etc.
The separate controller is that the theme part and the display are separated. The theme part is installed in the tool box, and the display is installed in the handlebar.
information about High Power Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/2020-new-model-high-power-electric-motorcycle.html
1. According to the power classification:
High power, medium power and low power, small power is more suitable for electric vehicles.
2. According to the motor classification:
Brushed and brushless, the speed adjustment method is to use the pulse width to modulate.
3. Classification according to structure:
Integral and separated:
The integrated controller is the controller and the display assembled together, installed in a small box, there will be many small holes on the box, you can see the working status of the electric car from the small holes. What is the speed, how much battery is left, etc.
The separate controller is that the theme part and the display are separated. The theme part is installed in the tool box, and the display is installed in the handlebar.
information about High Power Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/2020-new-model-high-power-electric-motorcycle.html
Is it certain that High Speed Electric Motorcycle manufacturers share the number of electric vehicle battery cycles?
Answer: The number of cycles is not necessarily the same. Some electric vehicles have a large depth of discharge, and the number of cycles is small, and some have a shallow depth of discharge. Naturally, more cycles are required, which mainly depends on the depth of discharge of the user.
Under normal circumstances, 100% of the discharge cycle is about 350 times, and 70% of the discharge is 550 times, 50% of the cycle is 1000 times, and so on. The shallower, the greater the cycle.
information about High Speed Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/racing-adult-high-speed-electric-motorcycle.html
Answer: The number of cycles is not necessarily the same. Some electric vehicles have a large depth of discharge, and the number of cycles is small, and some have a shallow depth of discharge. Naturally, more cycles are required, which mainly depends on the depth of discharge of the user.
Under normal circumstances, 100% of the discharge cycle is about 350 times, and 70% of the discharge is 550 times, 50% of the cycle is 1000 times, and so on. The shallower, the greater the cycle.
information about High Speed Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/racing-adult-high-speed-electric-motorcycle.html
Today, electric vehicles have become a part of everyone’s life. However, there are currently refurbished cars, assembled cars, and even stolen stolen cars on the market. It not only disrupts the benign competition in the electric vehicle market, but also brings huge potential safety hazards to consumers. Then the High Speed Electric Motorcycle manufacturer will teach you how to distinguish the inferior cars from these informal manufacturers?
1. See the inspection certificate. The original car has the inspection certificate when it leaves the factory, but the assembled car usually does not.
2. See if there is a manufacturer’s logo or steel stamp on each part of the vehicle.
3. Pay attention to check whether the frame number of the electric vehicle is consistent with the certificate number provided by the dealer.
4. Pay attention to check the "three guarantees" certificate of electric vehicles, and ask for bills and warranty cards.
5. Focus on checking the motor for signs of scratches, oil, dust, etc.
6. Look at the price. If the price is ridiculously low, we must be vigilant.
information about High Speed Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/racing-adult-high-speed-electric-motorcycle.html
1. See the inspection certificate. The original car has the inspection certificate when it leaves the factory, but the assembled car usually does not.
2. See if there is a manufacturer’s logo or steel stamp on each part of the vehicle.
3. Pay attention to check whether the frame number of the electric vehicle is consistent with the certificate number provided by the dealer.
4. Pay attention to check the "three guarantees" certificate of electric vehicles, and ask for bills and warranty cards.
5. Focus on checking the motor for signs of scratches, oil, dust, etc.
6. Look at the price. If the price is ridiculously low, we must be vigilant.
information about High Speed Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/racing-adult-high-speed-electric-motorcycle.html
The use of battery cars is now very extensive, so how to use battery cars correctly, many people are not very clear about how to use electric vehicles correctly, the following High Speed Electric Motorcycle suppliers will share it:
1. Don’t charge at high temperature: The combination of the two conditions will cause the temperature on the battery surface to rise rapidly when the weather is hot and the heat generated during charging. In a cool and dark place.
2. Do not charge immediately after driving: If the electric vehicle is charged immediately after driving at high temperature, it is easy to aggravate the increase in line temperature and the motor heat. In severe cases, it may even cause the battery to crack or deform, resulting in circuit failure and spontaneous combustion. Allow the battery to cool before charging.
information about High Speed Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/racing-adult-high-speed-electric-motorcycle.html
1. Don’t charge at high temperature: The combination of the two conditions will cause the temperature on the battery surface to rise rapidly when the weather is hot and the heat generated during charging. In a cool and dark place.
2. Do not charge immediately after driving: If the electric vehicle is charged immediately after driving at high temperature, it is easy to aggravate the increase in line temperature and the motor heat. In severe cases, it may even cause the battery to crack or deform, resulting in circuit failure and spontaneous combustion. Allow the battery to cool before charging.
information about High Speed Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/racing-adult-high-speed-electric-motorcycle.html
Next, what details should the High Power Electric Motorcycle manufacturer pay attention to when buying a battery car?
1. Check the appearance, see if the surface of the paint and electroplated parts is intact.
2. Follow the actual operation according to the manual to check the working status of the vehicle. The speed regulation transition should be smooth, no impact when starting, the wheels should rotate flexibly, without stagnation and weight, the wheel rotation sound should be soft, no abnormal noise, the brake should be moderately tight, and the brakes should be reliable.
3. Also check whether the auxiliary functions (such as power display, speed, mileage display, etc.) that the model should have are in a normal state.
4. Whether the accessory, charger, certificate, manual, and warranty card that accompany the vehicle are complete.
The above content is organized and shared by TAIZHOU SUQIER NEW ENERGY SCIENCE AND TECHNOLOGY CO.,LTD. ,Hoping to help those in need.
Next, what details should the High Power Electric Motorcycle manufacturer pay attention to when buying a battery car?
1. Check the appearance, see if the surface of the paint and electroplated parts is intact.
2. Follow the actual operation according to the manual to check the working status of the vehicle. The speed regulation transition should be smooth, no impact when starting, the wheels should rotate flexibly, without stagnation and weight, the wheel rotation sound should be soft, no abnormal noise, the brake should be moderately tight, and the brakes should be reliable.
3. Also check whether the auxiliary functions (such as power display, speed, mileage display, etc.) that the model should have are in a normal state.
4. Whether the accessory, charger, certificate, manual, and warranty card that accompany the vehicle are complete.
The above content is organized and shared by TAIZHOU SUQIER NEW ENERGY SCIENCE AND TECHNOLOGY CO.,LTD. ,Hoping to help those in need.
High Power Electric Motorcycle Manufacturers Share The Reason Why Battery Cars Have No Electricity
2020年5月21日A lot of friends who drive battery cars must have happened that the battery car suddenly stopped, and when it was charging, it was already a green light, but it seems that there is no electricity, then what to do, then the High Power Electric Motorcycle manufacturer will tell you how Will it matter?
First of all, you have to take a look at using your key to open it, to see if your pointer is rotating. If you do n’t have electricity, the pointer will still rotate. If the pointer does not rotate, then it may be the connection of your battery. Loose
If you do n’t have electricity, you can go outside and charge fast, or if you are close to where you live, just push it back, and then change a charger, because your charger is not working, it shows a green light There is no electricity, so it must be replaced
If you have loose wiring, then you can wire it yourself. First, open the cover of your car seat, and then you will find a board inside.
Then remove the board, unplug the battery of your first space, and then take out the battery
Then you will find there is a battery inside, so you need to take out this battery too, and then see if its wiring is loose. If it is loose, just connect it, then put everything back in place. , And then use the key to turn on to see if there is electricity, if you still do n’t have it, you can only repair it, the above is my method, I hope it is useful to everyone.
information about High Power Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/2020-new-model-high-power-electric-motorcycle.html
First of all, you have to take a look at using your key to open it, to see if your pointer is rotating. If you do n’t have electricity, the pointer will still rotate. If the pointer does not rotate, then it may be the connection of your battery. Loose
If you do n’t have electricity, you can go outside and charge fast, or if you are close to where you live, just push it back, and then change a charger, because your charger is not working, it shows a green light There is no electricity, so it must be replaced
If you have loose wiring, then you can wire it yourself. First, open the cover of your car seat, and then you will find a board inside.
Then remove the board, unplug the battery of your first space, and then take out the battery
Then you will find there is a battery inside, so you need to take out this battery too, and then see if its wiring is loose. If it is loose, just connect it, then put everything back in place. , And then use the key to turn on to see if there is electricity, if you still do n’t have it, you can only repair it, the above is my method, I hope it is useful to everyone.
information about High Power Electric Motorcycle : https://www.suqier.com/product/electric-motorcycle-series/2020-new-model-high-power-electric-motorcycle.html
Lithium batteries are increasingly used in simple electric bicycles, the following Fast Sport Electric Motorbike manufacturer shares what you need to pay attention to when charging a lithium battery for the first time.
1, lithium battery electric vehicle activation does not require a special method, in the electric vehicle driving lithium battery will naturally activate. If you deliberately want to use the circulating “first three 12-hour long charge activation ”method, then it will only be futile and have no effect.
2, when the lithium battery in the driving process of the electric vehicle battery is too low, the battery should be charged as soon as possible. (Fast charging stations are highly discouraged here, super damaged batteries. The market about the battery power consumption and recharge and battery long charge is not all right, it also depends on the type of battery, for “ try to the electric car battery power consumption, the best to run ” the practice, in fact, only used in the nickel battery, the purpose of course is to avoid the battery memory effect occurs.
3. Charge in accordance with standard time and procedure, even for the first three times; (in particular, do not make extra-long charges of more than 12 hours)
The above content is shared by TAIZHOU SUQIER NEW ENERGY SCIENCE AND TECHNOLOGY CO.,LTD. in the hope of helping those in need.
1, lithium battery electric vehicle activation does not require a special method, in the electric vehicle driving lithium battery will naturally activate. If you deliberately want to use the circulating “first three 12-hour long charge activation ”method, then it will only be futile and have no effect.
2, when the lithium battery in the driving process of the electric vehicle battery is too low, the battery should be charged as soon as possible. (Fast charging stations are highly discouraged here, super damaged batteries. The market about the battery power consumption and recharge and battery long charge is not all right, it also depends on the type of battery, for “ try to the electric car battery power consumption, the best to run ” the practice, in fact, only used in the nickel battery, the purpose of course is to avoid the battery memory effect occurs.
3. Charge in accordance with standard time and procedure, even for the first three times; (in particular, do not make extra-long charges of more than 12 hours)
The above content is shared by TAIZHOU SUQIER NEW ENERGY SCIENCE AND TECHNOLOGY CO.,LTD. in the hope of helping those in need.
1 2
